国产日韩综合精品_国产v欧美v日韩在线观看_无码一级在线观看中文字幕_日本熟女乱伦视频_自拍乱伦亚洲三级_国产成人男女在线观看网站_下药伦姧在线观看无码_开心激情网激情五月天_东京热一精品无码av_国产精品美女AV

  精密鋼管長度和外形有哪些要求？下面無縫鋼管廠就來給大家說說！

  國內現在一般廠家生產的精密鋼管的長度為2000～12000mm，對定尺和倍盡長度的規定為：精密鋼管定尺長度及倍尺總長度應在通常長度范圍內，當精密鋼管的長度≤5000mm時，全長允許偏差為0～5mm；長度＞5000mm時，全長允許偏差為0～10mm，每個倍尺長度的精密鋼管應留出的切口裕量為：外徑≤159mm時，留出的切口裕量為5～10mm；當精密鋼管的外徑＞mm時，留出的切口裕量為10～15mm。

  在對精密鋼管的外徑要求上，一般對精密鋼管的彎曲度應不大于3.0mm/m。外徑大于16mm的精密鋼管全長彎曲度按上屈服強度Reh的不同，應符合以下規定：Reh≤500MPa，≤0.15%L；Reh＞500MPa，≤0.20%L。如果精密鋼管的供求雙方經過協議，每米彎曲度和全長彎曲度可采用其他的規定。

  不圓度方面，精密鋼管的不圓度應不大于外徑公差的80%；當精密鋼管的壁厚不均，供求雙方應妥當協商。

  Precision steel tube length and shape what are the requirements?Seamless steel pipe to give us the below!

  Now the general domestic manufacturers in the production of precision steel tube length is 2000 ~ 12000 mm, the length of the length and times of provisions for: precision steel pipe specified length and times' total length should be the length range, usually when precision steel tube length is 5000 mm or less, total length of allowable deviation of 0 ~ 5 mm;Length > 5000 mm, the total length of the allowable deviation of 0 ~ 10 mm, each times ruler length of precision steel tube should be set aside the incision of allowance for: outer diameter 159 mm or less, to set aside the incision of allowance for 5 ~ 10 mm;When > mm precision steel tube diameter, set aside the incision of allowance for 10 ~ 15 mm.

  On the requirements of precision steel tube diameter, the general precision steel tube bending should be no greater than 3.0 mm/m.Diameter greater than 16 mm length of precision steel tube bending on the yield strength of the Reh, shall meet the following requirements: Reh acuities were 500 mpa, 0.15% or less L;Reh > 500 mpa, 0.20% or less L.If the supply and demand both sides precision steel tube agreement, bending per meter and the total length of bending can adopt the rules of the other.

  Out of roundness, the out of roundness of precision steel tube should be not greater than 80% of the outside diameter tolerance;When the precision of steel tube wall thickness uneven, both supply and demand should be appropriate to negotiate.